We're offline for a tune-up, we'll be up and running smoothly very soon. In the meantime, here are some other options available: Visit an  Sign up for View us on Social Media We appreciate your patience – for your next visit: 15% offyour next purchase. Enter coupon code: in shopping cart. We look forward to serving you, We're offline for a tune-up, we'll be up and running smoothly very soon. In the meantime, here are some other options available: Visit an Sign up for View us on Social Media We appreciate your patience – for your next visit: 15% offyour next purchase. Enter coupon code: in shopping cart. We look forward to serving you, Ford Fiesta Tail Light Bulbs Replacement Guide
Owners of other Ford or Lincoln vehicles such as the Focus, Fusion, C-Max, Mustang, Escape, Transit Connect, Edge, Flex, Explorer, Expedition, Taurus, F-150, EcoSport, MKC, MKZ, MKS, MKX, MKT and the Navigator may also find these DIY instructions to be helpful. Replacement bulbs with their part numbers are as follows: Brake # 3157K, Rear Turn Signal 3757NAK (or 3157NA) and Reverse Light # 921 (or W16W). The tools needed to complete this procedure include a star bit Torx T25 screwdriver and a plastic automotive panel pry tool. Loosen Counterclockwise T-25 Screw Removed Remove 2nd T25 Screw This guide was created with a Fiesta hatchback. The steps should be similar for the sedan models. Just open the trunk lid, pry out any plastic fasteners and pull back the trunk carpet liner to access the bulb sockets. Open the tailgate door on the rear end of the hatchback and move to the side of the vehicle with the burnt out bulb. Remove the two screws along the inner edge of the tail light housing by turning them counterclockwise with a Torx T25 star bit screwdriver. Set the two screws aside in a safe place. Two Screws Removed Pry At Outer Edge Pull Off Tail Light Housing The tail light housing is still held in place to the rear corner of the vehicle by two pegs or "spikes" inserted in to plastic grommets. Try to pull the tail light housing straight off the rear of the vehicle. If you have trouble removing it, carefully pry along the outer edge with a plastic automotive panel tool to loosen the two peg friction fasteners. Turn Over Assembly 1/4 Turn Counterclockwise Brake Light Bulb Socket Turn over the the housing and rest it on the bumper to access the bulb sockets. The Brake Light bulb socket is located at the middle of the housing. Rotate the bulb socket 1/4 turn counterclockwise and pull it straight out of the housing. Pull Out Old Bulb Push In New # 3157K Bulb Re-Insert Bulb Socket Pull the old bulb straight out of the socket and push in a new # 3157Kor 3157 bulb. Re-insert the bulb socket in to the housing and rotate it 1/4 turn clockwise to secure it in place. 1/4 Turn Clockwise - Lock 1/4 Turn Counterclockwise Pull Out Old # 3757NAK The Rear Turn Signal bulb socket is located near the bottom inner edge of the housing. Rotate the bulb socket 1/4 turn counterclockwise and pull it straight out of the housing. Turn Signal # 3757NAK Push In New Amber Bulb 1/4 Turn Clockwise - Lock Pull the old bulb straight out of the socket and push in a new amber colored # 3757NAKor 3157NAbulb. Re-insert the bulb socket in to the housing and rotate it one quarter turn clockwise to secure it in place. Reverse Bulb Socket 1/4 Turn Counterclockwise Old # 921 (W16W) Bulb The Reverse Bulb socket is located near the bottom outer edge of the housing. Rotate the socket 1/4 turn counterclockwise and pull it straight out of the housing. Pull the old bulb straight out of the socket. Push In New # 921 Bulb 1/4 Turn Clockwise - Lock Two Plastic Grommets Push a new # 921bulb straight in to the socket. Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to secure it in place. Line Up Pegs & Grommets Push On Tail Light Housing Tighten Top T-25 Screw Line up the two metal pegs or "spikes" on the rear outer edge of the tail light assembly with their corresponding grommets on the vehicle. Carefully push the tail light housing back in to place. Tighten Torx Clockwise Tail Light Assembly Replaced Test New Tail Light Bulbs Replace the two Torx T-25 screws and tighten them in the clockwise direction until they are snug. Try to avoid over tightening the screws to prevent from cracking the plastic inner edge of the tail light housing. Test the new tail light bulbs by having someone step on the brake pedal, activate the hazard signals and place the transmission in reverse. For more, check out my other 2009-2015 Ford Fiesta DIY Repair & Maintenance Guides. What bulbs does a Ford Fiesta use?Xenon HID Kits. |
2015 ford fiesta rear turn signal bulb replacement
Related Posts
Copyright © 2024 boxhoidap Inc.
