operating instructions, tips Show VEnT SEnSoR (DV50F9A8E(G)*) Your Samsung dryer is equipped with a Vent Sensor, which detects and notifies you when it is time to clean the ductwork. Keep your dryer safe and efficient by cleaning the ducts when prompted. The Vent Sensor detects any duct blockages You can fi gure out whether there is a duct blockage from the "Vent Sensor " lamp of the digital display. Level 0 The "Vent Sensor lamp is turned off . 1 The "Vent Sensor lamp illuminates. 2 The "Vent Sensor lamp blinks. In the LEVEL 2 state, this lamp blinks for 3 hours after the completion of the cycle. (If the wrinkle prevention function is activated, this message is displayed for up to 3 hours.) If the power button is pressed or the door is opened, the power is immediately turned off. For more information about the duct installation, please refer to the "Ducting requirements" section on page 10. • Although the dryer is available even if the blockage message is displayed, the drying time may be extended. • If the LEVEL 1 message is displayed the fi rst time the dryer is run after the installation, check the connection and clean the duct. If the LEVEL 1 message appears even after you have checked and cleaned the ducts, this may indicate that there are some restrictions of the duct due to the length, condition, etc. If this occurs, you can use the dryer normally and no countermeasures need to be taken. However, the drying time may be extended or the drying performance may be degraded. 30_ operating instructions, tips Message The ductwork is free from " blockages. " When a part of the duct or the lint fi lter is blocked by lint or a foreign object. When the resistance is high because the duct is too long or bent. " When the duct is blocked by lint or a foreign object. When the resistance is very high because the duct is too long or bent excessively. Status Solution - Check the duct connection and shorten the duct and straighten it if necessary. Check the lint fi lter or the duct and clean it if necessary. Check the duct connection and shorten the duct and straighten it if necessary. Check the lint fi lter or the duct and clean it as soon as possible.
Just got my new washer installed. Went to use the Smart Care option, but would not allow permission to access to my location, contact list, or the ability to record. So unfortunately, I will not be able to see anything in this app aside from a message telling me to go to settings and allow these permissions. Why does Samsung need to access my contact list, location, and have the ability to record me? 196 people found this review helpful
The app requires permission to access contacts, phone, camera, and location. It does require the camera for linking to the washer and dryer, but there is no reason to need access to everything else. On top of that, if you deny it access to even one of these, it will close the app and not allow you to proceed any further until you allow it access to all it wants. I refused, so in the end I never did get to test if it will connect or how well it works and I won't. Uninstalled until resolved. 341 people found this review helpful
I just got these and given the layout of my house was happy to see that I could get an app for monitoring these machines. Unfortunately the permissions are so invasive, contacts, location all the time, record video, that I won't be using this app and am trying to find the module in the machine to disable it. I couldn't even get it to work after giving it all the invasion of my privacy. 144 people found this review helpful
© US Appliance 2022. All Rights Reserved. Why is my Samsung dryer not drying my clothes?If your dryer is heating but the clothes are still damp, your vent is probably blocked. If your dryer has weak heat and runs for a long time, that could also be a blocked vent. And if your dryer ends after only a couple minutes with soaking wet clothes, your moisture sensors could be dirty.
What are the symbols on my Samsung dryer?Dryer Icons. Sensor Dry. This icon indicates a Sensor Dry cycle is currently running.. Child Lock. Child Lock is turned on. ... . Delay Start. Delay Start is in use. ... . Filter Reminder. This icon displays after every load as a reminder to clean the lint filter. ... . Time Remaining. ... . Signal Off. ... . Mixed Load Bell. ... . Vent Check.. How do you check the moisture sensor on a Samsung dryer?The sensor bars can be also tested in diagnostic mode. Place a slightly damp cloth in the dryer, start a normal cycle then press the Temp + Signal buttons for 3 seconds. When there are wet items being dried, data will add up (from 0 to 1200 and repeating) as the wet clothes touch the sensor bars.
|