WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
NOTE: This washer does not include inlet hoses.
See the Installation Instructions for more information.
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Ef ciency (HE) detergents and follow the
HE detergent manufacturer's instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to
help dry out the washer and prevent the buildup of
odor-causing residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This
Washer Maintenance Procedure should be performed,
at a minimum, once per month or every 30 wash cycles,
whichever occurs sooner, to control the rate at which soils
and detergent may otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above, and use this recommended monthly
cleaning procedure:
Clean Washer Cycle
This washer has a special cycle that uses higher water
volumes in combination with affresh
or liquid chlorine bleach to clean the inside of the washer.
Begin procedure
1. affresh
Washer Cleaner Cycle Procedure
®
(Recommended for Best Performance):
a. Open the washer lid and remove any clothing or items.
b. Place an affresh
®
Washer Cleaner tablet in the bottom
of the washer basket.
c. Do not place an affresh
in the detergent dispenser.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer lid.
f. Select the CLEAN WASHER cycle.
g. Press the START/PAUSE button to begin the cycle.
The Clean Washer Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER. (For models with no
Power button, press and hold START/PAUSE for three
seconds). After the Clean Washer cycle has stopped, run
a Rinse/Drain & Spin cycle to rinse cleaner from washer.
12
®
Washer Cleaner
®
Washer Cleaner tablet
WASHER CARE (cont.)
2. Chlorine Bleach Procedure (Alternative):
a. Open the washer lid and remove any clothing
or items.
b. Add 1 cup (236 mL) of liquid chlorine bleach
to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
e. Select the CLEAN WASHER cycle.
f. Press the START/PAUSE button to begin the cycle.
The Clean Washer Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER. (For models with no
Power button, press and hold START/PAUSE for three
seconds). After the Clean Washer cycle has stopped, run
a Rinse/Drain & Spin cycle to rinse cleaner from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will ll to a water level higher than in normal
wash cycles to provide rinsing at a level above the water
line for normal wash cycle.
2. During this cycle, there will be some agitation and
spinning to increase the removal of soils.
After this cycle is complete, leave the lid open to allow
for better ventilation and drying of the washer interior.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
IMPORTANT: To avoid damaging the washer's nish, do not
use abrasive products.
Guess how to clean the Whirlpool Cabrio washer? If you are still wondering why your washer has a stinky odor even after you wash it with bleach or washer cleaner, then read further.
This time around, try to clean your Whirpool Cabrio washer properly and remove all those nasty smells.
Don’t worry; I have listed down the steps that you must consider while cleaning your washer. Your washer requires cleaning. After all, it cleans all your stuff. A washer needs to be cleaned appropriately once every 30 cycles or at least once a month. It will help your washer refresh, get off with the foul odors, and cut off the molds. Cleaning your laundry is as much as important as taking care of your washer. Even if you have a front load washer, top load washer, or any washer, they must be clean. It will remove the foul odor, destroy the bacteria and limescale build-up. There is so much more to know, so read along!
Rinsing your washer may not be enough. As your washer focuses on cleaning your clothes every cycle, the bacteria goes somewhere and might cause respiratory problems and nasty smells and create dark spots in your washer. So, cleaning your washer is essential to avoid or prevent it from reoccurring. In addition, you can set a date to clean it up, making sure you won’t forget. If you want to clean your washer today or tomorrow, it is vital to clean it properly. We often thought that rinsing it after use is good to go, but sad to say, and it isn’t. So follow these steps on how to clean the Whirlpool Cabrio washer:
Step #1. Empty the drum
Open the lid or the door of your washer. If you have put your clothes in the washer or have kept some items inside the washer, pull them out first or remove them. It is always better not to put anything inside the drum, as this may cause a foul odor.
Step #2. Prepare your washer cleaner
There are several washer cleaner powders and tablets which you can consider using. You can take a look at them online or buy them in stores nearby. It is to use in cleaning the washer, and effective more than the regular detergents.
Step #3. Place your washer cleaner
Pour your washer cleaner into the washer’s basket or drum. Be careful not to pour the washer cleaner into your detergent dispenser, as it may have different effects on your clothes while loading a cycle. Adding other chemicals while cleaning the washer with a washer cleaner is not recommended.
Step #4. Begin the cycle
Close the lid or the door of your washer. Next, tap the Clean washer that is in your Whirlpool Cabrio washer. After that, press the Start/Pause button for at least 3 seconds to begin the cycle.
Step #5. After the cycle
After the washer finishes the cycle, tap the spin and rinse. It will flush the cleaner. It is advisable to open the lid and leave it to dry the washer and prevent odor-causing residue from building up. Then, voila, it’s done. If your washer doesn’t have a clean washer button, you can clean your washer by using hot water and a cup of chlorine to your washer. Then, spin it in a regular cycle and rinse it off after. Leave your washer\s lid or door open to dry it up.
The Importance of Cleaning Your Washer
After using the washer several times a week, the sticky, detergent residues, bacterias, and molds from your clothes will start to build up somewhere. I have listed three primary reasons why you need to clean your washer and how it affects its performance. It will also help you understand the importance of cleaning your washer.
#1. Respiratory problems
You might not have heard this yet, but this happens. As you wash your clothes to remove the dirt using your washer, your washer collects and might distribute the bacteria instead of only removing them. The mold might trigger an allergic reaction or asthma symptoms for those individuals who are allergic to the molds.
#2. Black residue
This black residue is from the soap or detergent residue that build-up in the lid or the washer’s door. At other times, it’s spotted inside the drum or basket as well. This residue may stick into your clothes and leave black marks.
#3. Black spots in clothes
If you notice black marks in your clothes after using the washer, it may also be caused by the limescale. This limescale is a white chalky residue that seen in the machine. Aside from this, it will also cause breakdowns to some parts of the washer.
#4. Bothersome odor
A foul odor may come into unusual smells. Some say it smells obnoxious, stinky, and offensive odors, but they are all caused by the same bacteria and molds. The scent will get stuck into your clothes even after rinsing them. Cleaning the washer will remove the odors and won’t cause odors in clothes. Know why does my washer smell and how to prevent and clean it.
It’s a Wrap!
Hopefully, you now have new ideas into when or how to clean the Whirlpool Cabrio washer. A clean washer will significantly affect your washer’s capability and performance. Monitoring and cleaning your washer at least once a month is necessary to achieve lesser maintenance and damages. Also, read about how to clean mold from the front load washer gasket and how to clean washer drain hoses.