195244 Show
Where is the lint filter located?Where is the lint filter located on a Model # 11091551210 - Kenmore Washer Is this a good question? Score 4
Chosen Solution
Hi, Sears has a lot of helpful diagrams about Kenmore washers. Here is a link to their site's information about the Model #11091551210. The diagrams on that page should aid you in locating the Lint Filter. Best of luck, and I hope this helps! Was this answer helpful? Score 4
I have a Kenmore series 700s top load Elite HE that does not have a filter either. There is a coin trap on the bottom of the tub instead. I had the “drn” error code today. Unplug the power from the wall jack. Keep a small bucket handy to catch water when removing hoses. Make sure power is disconnected. The external hose was clear so I removed the back panel (7 hex head screws) and also removed screw that holds the plastic drain hose connection to the back of the washer. Tilt the washer forward and place a block or something under the back feet to keep it from falling and give u to it some room to work. The drain pump is on the back side of the tub. Remove the short hose that connects the bottom of the tub to the drain pump and you will likely find a clog in that hose or lint/hair/etc. hung up on the coin trap mentioned earlier. Clean the clog and re-assemble. Was this answer helpful? Score 0 Download Article Download Article Problems with your washing machine can be infuriating, especially when your clothes are soaking wet after the final spin. Luckily, checking and cleaning your washing machine filter is a quick and easy process. By locating and removing your filter, cleaning it, and taking steps to prolong your filter’s life, you can save yourself hundreds of dollars in repairs. Washing machine filters should be cleaned every 3-4 months.
Advertisement
Advertisement
Advertisement Ask a Question 200 characters left Include your email address to get a message when this question is answered. Submit Advertisement
Advertisement ReferencesAbout This ArticleArticle SummaryX Before cleaning the filter on your washing machine, power the machine down and unplug it. Lay some old towels down on the floor in front of the machine in case any water leaks out when you remove the filter. If you have a front-loading or older top-loading washer, the filter is usually located in the lower right corner of the machine. However, many newer top-loading models have a filter inside the machine, underneath the agitator. Once you locate the filter, take the cover off. You may need to pry it off with a screwdriver. Then, grab the handle on the filter and pull it out. Wipe any excess lint and residue off the filter with a paper towel, then remove the screen from the filter and soak it in hot water for 10 minutes. Look inside the washing machine for any loose lint and wipe it out before sliding the filter back into place and replacing the cover. Run the washing machine on a regular cycle without any laundry in it and check for leaks to make sure that you put the filter back in correctly. To learn how to prolong the life of your filter, keep reading! Did this summary help you? Thanks to all authors for creating a page that has been read 269,282 times. Reader Success Stories
Did this article help you?Do top loading washing machines have filters to clean?“Top loaders tend to have filters on the valves,” said Amber Peabody, Service Manager at Dunnett Inc. The valve filters sift the water going in and out of the pump and hoses. If you do happen to have a removable filter, consult your owner's manual on how to properly remove it.
How do I find the filter on my top load washing machine?Where is the Filter on a Washing Machine?. In the front of the unit behind a small hatch.. At the end of the drainage hose.. Under the cover of your center agitator.. Along the top rim of the drum of your washing machine.. Where is the filter on an old Kenmore washer?Locate the filter
The filters in the Kenmore Top Load washing machine are usually located beneath the agitator if it's an agitator-based model. To get access to the Kenmore top load filter, you need to unscrew the screws holding the agitator. Then, detach the agitator.
|